The Recombination Engine from Future Sound Systems is a triple analogue voltage-controlled oscillator Eurorack module with a focus on a novel wave-splicing technique.
The Recombination method can produce new, harmonically-rich timbres. Each oscillator is built around a new-generation CEM 3340 VCO chip to ensure ultimate tracking and linearity across the frequency spectrum, as per necessary for several features of the Recombination technique.
The OSC2 employs its three VCOs in a master / positive-slave / negative-slave arrangement – the output of which is found at the Glue section. The Scissor section can be used as a master oscillator, which, in the Recombination technique, is used to switch between the Positive and Negative DNA oscillators, dependent on the positive or negative state of the Scissor square-wave. Sinusoidal, triangle and ramp waveforms can be mixed at each DNA VCO through SSI2164-based VCA sections, the mixed outputs of which are switched between at the Glue section in accordance to the Scissor.
The VCOs of the OSC2 also allow for switchable linear or exponential FM and offer very wide frequency ranges between Coarse and Fine tune controls. Both DNA oscillators' VCA sections are accessible through the Mix Outputs, with the level controls operating in a similar fashion to those found on our Cyclical Engine VCO module. At 12 o'clock, each waveform is modulated at full-scale by the applicable positive or negative state of the Scissor VCO's square-wave. At 5 o'clock, each waveform flows through its VCA at full scale. Meanwhile, each waveform is available pre-VCA at the Raw Outputs.
As part of the Scissor section, three modulation busses can be switched on and off. PW Skew ties the pulsewidth modulation bus of the Scissor VCO to the frequency busses of the DNA VCOs. This means that, if the positive region of the Scissor VCO's square-wave is elongated as the pulsewidth is increased, the frequency of the Positive DNA VCO is decreased, so that the positive portion of the Glue waveform becomes "stretched out". The opposite happens to the negative portion of the Glue waveform in this instance, so becomes condensed. This effect is particularly useful for creating formant-type timbres at the Glue output.
CV Lock between the three VCOs ties the exponential frequency bus of the Scissor oscillator to the two DNA VCOs. This is especially useful when using the OSC2 as a standard triple oscillator stack, as found in classic subtractive synthesizers. Sync Lock resets the Positive DNA to the positive portion of the Scissor VCO's square-wave, and resets the Negative DNA to the Scissor's negative portion. There is also a switch in the Scissor section to shift the entirety of the OSC2 between low and audible frequency ranges.
Technical specifications:
Module width: 32HP
Module depth: 50mm behind 2mm FR4 front panel
Current draw: +170, -120 mA
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK, 'next working day' shipping is free if the order value is over £150, and £5 otherwise. We can also ship on a 'next working day before 12pm' service, which costs £6 for orders over £150 and £7.50 for orders under £150.
Shipping to mainland EU typically costs between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of DPD, Royal Mail and Parcelforce for the UK, and for international orders it's either DHL, FedEx, UPS, Royal Mail or Parcelforce depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we aim to dispatch the same working day if we get the order before 16:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes the couriers may come to collect a little earlier than scheduled which would also push an order into the next day.
Saturday/Sunday shipping
If you're in the UK and you order before 16:00 on a Friday then we can send something for a Saturday or Sunday delivery with DPD. This is FREE for order values over £350, £5 for order values between £75 and £250, and £7 for order values under £75. (NB: this applies to UK mainland addresses only). Please note that any orders placed after 16:00 on a Friday will ship on the Monday.
International shipping times
Since April 2020, the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer. There is absolutely nothing we can do about this, unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
Product Overview
The Recombination Engine from Future Sound Systems is a triple analogue voltage-controlled oscillator Eurorack module with a focus on a novel wave-splicing technique.
The Recombination method can produce new, harmonically-rich timbres. Each oscillator is built around a new-generation CEM 3340 VCO chip to ensure ultimate tracking and linearity across the frequency spectrum, as per necessary for several features of the Recombination technique.
The OSC2 employs its three VCOs in a master / positive-slave / negative-slave arrangement – the output of which is found at the Glue section. The Scissor section can be used as a master oscillator, which, in the Recombination technique, is used to switch between the Positive and Negative DNA oscillators, dependent on the positive or negative state of the Scissor square-wave. Sinusoidal, triangle and ramp waveforms can be mixed at each DNA VCO through SSI2164-based VCA sections, the mixed outputs of which are switched between at the Glue section in accordance to the Scissor.
The VCOs of the OSC2 also allow for switchable linear or exponential FM and offer very wide frequency ranges between Coarse and Fine tune controls. Both DNA oscillators' VCA sections are accessible through the Mix Outputs, with the level controls operating in a similar fashion to those found on our Cyclical Engine VCO module. At 12 o'clock, each waveform is modulated at full-scale by the applicable positive or negative state of the Scissor VCO's square-wave. At 5 o'clock, each waveform flows through its VCA at full scale. Meanwhile, each waveform is available pre-VCA at the Raw Outputs.
As part of the Scissor section, three modulation busses can be switched on and off. PW Skew ties the pulsewidth modulation bus of the Scissor VCO to the frequency busses of the DNA VCOs. This means that, if the positive region of the Scissor VCO's square-wave is elongated as the pulsewidth is increased, the frequency of the Positive DNA VCO is decreased, so that the positive portion of the Glue waveform becomes "stretched out". The opposite happens to the negative portion of the Glue waveform in this instance, so becomes condensed. This effect is particularly useful for creating formant-type timbres at the Glue output.
CV Lock between the three VCOs ties the exponential frequency bus of the Scissor oscillator to the two DNA VCOs. This is especially useful when using the OSC2 as a standard triple oscillator stack, as found in classic subtractive synthesizers. Sync Lock resets the Positive DNA to the positive portion of the Scissor VCO's square-wave, and resets the Negative DNA to the Scissor's negative portion. There is also a switch in the Scissor section to shift the entirety of the OSC2 between low and audible frequency ranges.
Technical specifications:
Module width: 32HP
Module depth: 50mm behind 2mm FR4 front panel
Current draw: +170, -120 mA
Technical Specs
Shipping Details
How much is my shipping?
Shipping is automatically calculated before you submit your payment information. Simply add items to your cart and proceed to the checkout page, where you'll be offered shipping options and their prices. In the UK, 'next working day' shipping is free if the order value is over £150, and £5 otherwise. We can also ship on a 'next working day before 12pm' service, which costs £6 for orders over £150 and £7.50 for orders under £150.
Shipping to mainland EU typically costs between £7 and £20, depending on the shipping method and the size and weight of the order.
Do you ship to my country?
Almost certainly - the site will give you an estimate of shipping costs if you add an item to the cart and then enter your country and postcode. If you have specific requirements (such as if you prefer UPS over FedEx, for example) then let us know in advance and we'll try to work something out for you.
Shipping methods
We use a combination of DPD, Royal Mail and Parcelforce for the UK, and for international orders it's either DHL, FedEx, UPS, Royal Mail or Parcelforce depending on where you are in the world. If you have a particular preference then try to let us know BEFORE you order so we can look into it for you. Please note that there may occasionally be additional shipping charges if you live in a remote area, depending on what surcharges are applied by the shipper. We'll get in touch to discuss this with you in such cases.
Dispatch times
For UK orders, we aim to dispatch the same working day if we get the order before 16:00. If you have a really urgent situation then of course drop us an email before ordering and we'll always do our absolute best to accommodate you.
For international orders, we normally dispatch the same day if we get the order before 13:00 but again, occasionally it might be the next day before we can send it out, and sometimes the couriers may come to collect a little earlier than scheduled which would also push an order into the next day.
Saturday/Sunday shipping
If you're in the UK and you order before 16:00 on a Friday then we can send something for a Saturday or Sunday delivery with DPD. This is FREE for order values over £350, £5 for order values between £75 and £250, and £7 for order values under £75. (NB: this applies to UK mainland addresses only). Please note that any orders placed after 16:00 on a Friday will ship on the Monday.
International shipping times
Since April 2020, the couriers we use have suspended guarantees for shipping times, so even though we're paying them for priority services - 24-48 hours for most of the world - in practice it's often an extra day on top and sometimes it can be longer. There is absolutely nothing we can do about this, unfortunately. If you are outside the UK and it's a life-or-death situation where you absolutely MUST have that passive mult for the next day then... it may be better to find a local supplier.
Pre-orders
If a product is listed as a pre-order, it means we've ordered it from the supplier but it's not physically in stock yet. The product listing will include an estimated shipping date based on the best information we have from the supplier, but do bear in mind this is subject to change and is not a guaranteed date.
If you place an order containing a mixture of in-stock and pre-order items, we'll normally hold off on shipping anything until the pre-order item(s) have arrived, rather than splitting it into multiple shipments. If you need the in-stock items sooner, we'd recommend placing separate orders. As always, please get in touch if you have questions.
